Eigenvalue Buckling Prediction In The Abaqus Standard Users Manual

1. Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 1
2. Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual Software
3. Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 2017
4. Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual Pdf
5. Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 2016

Abaqus/Standard contains a capability for estimating elastic buckling by eigenvalue extraction. This estimation is typically useful for “stiff” structures, where the prebuckling response is almost linear. The buckling load estimate is obtained as a multiplier of the pattern of perturbation loads, which are added to a set of base state loads.

Panasonic Cordless Telephone User Manuals. Panasonic 58ghz Cordless Phone Manual Add to Favourites. This unit is compatible with Caller ID. You must subscribe to the appropriate service offered by your service provider/telephone company. Please read these operating instructions before using the unit and save them for future. Panasonic caller id phone user manual.

In an eigenvalue buckling problem we look for the loads for which the model stiffness matrix becomes singular, so that the problem

has nontrivial solutions. is the tangent stiffness matrix when the loads are applied, and the are nontrivial displacement solutions. The applied loads can consist of pressures, concentrated forces, nonzero prescribed displacements, and/or thermal loading.

Eigenvalue buckling is generally used to estimate the critical buckling loads of stiff structures (classical eigenvalue buckling). Stiff structures carry their design loads primarily by axial or membrane action, rather than by bending action. Their response usually involves very little deformation prior to buckling. A simple example of a stiff structure is the Euler column, which responds very stiffly to a compressive axial load until a critical load is reached, when it bends suddenly and exhibits a much lower stiffness. However, even when the response of a structure is nonlinear before collapse, a general eigenvalue buckling analysis can provide useful estimates of collapse mode shapes.

The buckling loads are calculated relative to the base state of the structure. If the eigenvalue buckling procedure is the first step in an analysis, the initial conditions form the base state; otherwise, the base state is the current state of the model at the end of the last general analysis step (see “General and linear perturbation procedures,” Section 6.1.2). Thus, the base state can include preloads (“dead” loads), . The preloads are often zero in classical eigenvalue buckling problems.

If geometric nonlinearity was included in the general analysis steps prior to the eigenvalue buckling analysis (see “General and linear perturbation procedures,” Section 6.1.2), the base state geometry is the deformed geometry at the end of the last general analysis step. If geometric nonlinearity was omitted, the base state geometry is the original configuration of the body.

Product: ABAQUS/Standard

ABAQUS/Standard contains a capability for estimating elastic buckling by eigenvalue extraction. This estimation is typically useful for “stiff” structures, where the prebuckling response is almost linear. The buckling load estimate is obtained as a multiplier of the pattern of perturbation loads, which are added to a set of base state loads. The base state of the structure may have resulted from any type of response history, including nonlinear effects. It represents the initial state to which the perturbation loads are added. The response to the perturbation loads must be elastic up to the estimated buckling load values for the eigenvalue estimates to be reasonable.

The following physical problem is addressed in eigenvalue buckling analysis: from an arbitrarily achieved base configuration with stresses in equilibrium with surface traction and body forces , we consider an elastic deformation with “small” displacement gradients under additional surface tractions , body forces , and boundary displacements , where the additional tractions and displacements are applied on mutually complementary parts of the boundary. Such a deformation is a linear perturbation on a predeformed state. A consistent application of the small-displacement gradient assumption to the kinematics and the constitutive equation from an initially stressed state leads to the solution of a linear problem as the response to the additional loading. Since the problem is linear, if is the stress response to the loads , , and , then for loads , , and the stress response will be .

Each distinct value of corresponds to a linear perturbation of the base state. Among these perturbed states we seek special values of that allow for the existence of nontrivial incremental displacement fields with arbitrary magnitudes as valid solutions to the problem. Such nontrivial incremental displacement fields are referred to as buckling modes. In the buckling analysis procedure in ABAQUS we do not distinguish between the geometry of the base state and the linearly perturbed configurations. As a result of this assumption we can seek the buckling modes as incremental displacements out of the base state geometry with stresses , applied tractions , and applied body forces .

Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 1

The equations of equilibrium for an arbitrarily chosen configuration during buckling, referred to as the current configuration, are written in terms of the nominal stress in the base state. If represents the position of a material point in the base state, the equilibrium equations can be expressed as

where is an arbitrary virtual velocity field, is the nominal traction on the boundary of the body in the base state, represents the body force per unit volume in the base state, and is the volume that the body occupies in the base state. The corresponding rate form is given by

Since we have assumed that the base state and the current state are indistinguishable, we now proceed to express the left-hand side in terms of the rate of Kirchhoff stress , the velocity gradient , the virtual velocity gradient , and the deformation gradient . Using the relations , where is the Kirchhoff stress based on the base state as the reference configuration, and , Equation 2.3.1–1 takes the form

We now use the relation between the rate of Kirchhoff stress , the material spin , and the Jaumann rate of Kirchhoff stress to transform this expression intoIn addition, we can replace the Kirchhoff stress with the Cauchy stress since it is assumed that the current and reference configurations are indistinguishable.

For the right-hand side of Equation 2.3.1–1 we note that the nominal tractions and body forces are given by and , where and are the elements of surface area and volume in the current configuration. For any material point the changes in and during buckling are completely characterized by the change of the deformation gradient at that point; loosely speaking, the magnitude of the applied forces at any material point is kept fixed, and the change in the applied tractions and body force intensities arises due to the change in geometry. For example, for a pressure load the magnitude of the pressure remains constant but the surface normal changes—a change that is completely characterized by the change in the deformation gradient. Since the ratios of the surface area and volume measures between the reference and current configurations can be viewed as functions of the deformation gradient only, it follows that and at any given material point also change only through their dependence on the deformation gradient; hence, their rates of change can be written as

or when the current and reference configurations are indistinguishable, Assuming a hypoelastic constitutive law, where is a fourth-order tensor that can depend on the current stress, the governing equation for the buckling analysis becomes where and are the nominal tractions generated during buckling corresponding to the base state tractions and the linear perturbation tractions , respectively; similar definitions apply for the nominal body force terms. The constitutive relation can represent elasticity, hypoelasticity, and hyperelasticity; rate effects and plasticity are ignored. The effective moduli are evaluated for the value of the stress and deformation in the base state.

Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual Software

To derive the finite element discretization for the expression above, we introduce the interpolated velocity field

Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 2017

where represents the position in the base state. Using the standard finite element approach, the governing equations for buckling then take the form of the standard eigenvalue problem:where is the base state stiffness and is the differential stiffness. The base state stiffness is the sum of the hypoelastic tangent stiffness, the initial stress stiffness, and the load stiffness: where and are the derivatives of the nominal surface tractions and body forces with respect to the nodal displacements. Since we do not distinguish between the current configuration and the reference configuration, the partial derivatives appearing in the load stiffness terms are all evaluated at corresponding to . For example, the load stiffness term for the surface tractions appearing in Equation 2.3.1–2,transforms into the finite element expressionwithThe differential stiffness consists of the sum of the initial stress stiffness due to the perturbation stresses and the load stiffness due to the perturbation loads: The contribution in this expression that is derived from the stress is symmetric; however, the contribution derived from the applied loads (the load stiffness) is symmetric only if the applied loading is conservative—that is, if the loads can be derived from an energy potential. If the load stiffness is nonsymmetric, the contribution will be symmetrized since ABAQUS can solve eigenvalue problems only with symmetric matrices.

Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual Pdf

If the generalized nodal “loads” resulting from both applied forces and as well as prescribed displacements are denoted by and those due to , , and are denoted by , the eigenvalues represent the multipliers that provide the estimated generalized buckling load as , while the corresponding eigenvectors give the associated buckling modes. Although in most analyses the lowest mode is the only one of interest, ABAQUS is able to extract several modes simultaneously. It is also worth noting that the common case of an antisymmetric buckling mode on a symmetric base state and buckling load is easily done with ABAQUS.

Do one of the following: My Passport Wireless Pro User Manual. Page 44. For a Windows PC, in the left pane of the File Explorer window, click Network MYPASSPORT SD. For a Mac computer, in the left pane of the Finder window in the SHARED section, double-click MYPASSPORT SD My Passport Wireless Pro User Manual. My passport wireless pro 1tb user manual.

Eigenvalue Buckling Prediction In The Abaqus Standard User's Manual 2016

If the tangent stiffness is predicted poorly by (that is, the structure is not “stiff” in the sense that the response is nonlinear prior to buckling), a nonlinear analysis using the Riks method is required to obtain a reliable estimate for the load carrying capacity of the structure.

Canon m50 manual download. Or Canon Canada, or a Canon authorized service provider for the Product. Loss of or damage to the Product due to abuse, mishandling, improper packaging by you, alteration, accident, electrical current fluctuations, failure to follow operating, maintenance or environmental instructions prescribed in Canon U.S.A.' S or Canon Canada's user's manual or services performed by someone other than Canon U.S.A. Without limiting the foregoing, water damage, sand/corrosion damage, battery leakage, dropping the Product, scratches, abrasions or damage to the body, lenses or LCD display or damage to the any of the accessories mentioned in the first paragraph above will be presumed to have resulted from misuse, abuse or failure to operate the Product as set forth in the operating instructions.